diff options
Diffstat (limited to 'platforms')
| -rw-r--r-- | platforms/avr/mcu_selection.mk | 95 | ||||
| -rw-r--r-- | platforms/chibios/mcu_selection.mk | 825 |
2 files changed, 920 insertions, 0 deletions
diff --git a/platforms/avr/mcu_selection.mk b/platforms/avr/mcu_selection.mk new file mode 100644 index 0000000000..c49818fbfb --- /dev/null +++ b/platforms/avr/mcu_selection.mk @@ -0,0 +1,95 @@ +ifneq (,$(filter $(MCU),at90usb162 atmega16u2 atmega32u2 atmega16u4 atmega32u4 at90usb646 at90usb647 at90usb1286 at90usb1287)) + PROTOCOL = LUFA + + # Processor frequency. + # This will define a symbol, F_CPU, in all source code files equal to the + # processor frequency in Hz. You can then use this symbol in your source code to + # calculate timings. Do NOT tack on a 'UL' at the end, this will be done + # automatically to create a 32-bit value in your source code. + # + # This will be an integer division of F_USB below, as it is sourced by + # F_USB after it has run through any CPU prescalers. Note that this value + # does not *change* the processor frequency - it should merely be updated to + # reflect the processor speed set externally so that the code can use accurate + # software delays. + F_CPU ?= 16000000 + + # LUFA specific + # + # Target architecture (see library "Board Types" documentation). + ARCH = AVR8 + + # Input clock frequency. + # This will define a symbol, F_USB, in all source code files equal to the + # input clock frequency (before any prescaling is performed) in Hz. This value may + # differ from F_CPU if prescaling is used on the latter, and is required as the + # raw input clock is fed directly to the PLL sections of the AVR for high speed + # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' + # at the end, this will be done automatically to create a 32-bit value in your + # source code. + # + # If no clock division is performed on the input clock inside the AVR (via the + # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. + F_USB ?= $(F_CPU) + + # Interrupt driven control endpoint task + ifeq (,$(filter $(NO_INTERRUPT_CONTROL_ENDPOINT),yes)) + OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + endif + ifneq (,$(filter $(MCU),at90usb162 atmega16u2 atmega32u2)) + NO_I2C = yes + endif +endif + +ifneq (,$(filter $(MCU),atmega32a)) + # MCU name for avrdude + AVRDUDE_MCU = m32 + + PROTOCOL = VUSB + + # Processor frequency. + # This will define a symbol, F_CPU, in all source code files equal to the + # processor frequency in Hz. You can then use this symbol in your source code to + # calculate timings. Do NOT tack on a 'UL' at the end, this will be done + # automatically to create a 32-bit value in your source code. + F_CPU ?= 12000000 +endif + +ifneq (,$(filter $(MCU),atmega328p)) + # MCU name for avrdude + AVRDUDE_MCU = m328p + + PROTOCOL = VUSB + + # Processor frequency. + # This will define a symbol, F_CPU, in all source code files equal to the + # processor frequency in Hz. You can then use this symbol in your source code to + # calculate timings. Do NOT tack on a 'UL' at the end, this will be done + # automatically to create a 32-bit value in your source code. + F_CPU ?= 16000000 +endif + +ifneq (,$(filter $(MCU),atmega328)) + # MCU name for avrdude + AVRDUDE_MCU = m328 + + PROTOCOL = VUSB + + # Processor frequency. + # This will define a symbol, F_CPU, in all source code files equal to the + # processor frequency in Hz. You can then use this symbol in your source code to + # calculate timings. Do NOT tack on a 'UL' at the end, this will be done + # automatically to create a 32-bit value in your source code. + F_CPU ?= 16000000 +endif + +ifneq (,$(filter $(MCU),attiny85)) + PROTOCOL = VUSB + + # Processor frequency. + # This will define a symbol, F_CPU, in all source code files equal to the + # processor frequency in Hz. You can then use this symbol in your source code to + # calculate timings. Do NOT tack on a 'UL' at the end, this will be done + # automatically to create a 32-bit value in your source code. + F_CPU ?= 16500000 +endif diff --git a/platforms/chibios/mcu_selection.mk b/platforms/chibios/mcu_selection.mk new file mode 100644 index 0000000000..6b6488466b --- /dev/null +++ b/platforms/chibios/mcu_selection.mk @@ -0,0 +1,825 @@ +ifneq ($(findstring MKL26Z64, $(MCU)),) + # Cortex version + MCU = cortex-m0plus + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 6 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = KINETIS + MCU_SERIES = KL2x + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= MKL26Z64 + + # Startup code to use + # - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= kl2x + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= PJRC_TEENSY_LC +endif + +ifneq ($(findstring MK20DX128, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = KINETIS + MCU_SERIES = K20x + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= MK20DX128 + + # Startup code to use + # - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= k20x5 + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= PJRC_TEENSY_3 +endif + +ifneq ($(findstring MK20DX256, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = KINETIS + MCU_SERIES = K20x + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= MK20DX256 + + # Startup code to use + # - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= k20x7 + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= PJRC_TEENSY_3_1 +endif + +ifneq ($(findstring MK64FX512, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = KINETIS + MCU_SERIES = K60x + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= MK64FX512 + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= k60x + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= PJRC_TEENSY_3_5 +endif + +ifneq ($(findstring MK66FX1M0, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = KINETIS + MCU_SERIES = MK66F18 + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= MK66FX1M0 + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= MK66F18 + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= PJRC_TEENSY_3_6 +endif + +ifneq ($(findstring RP2040, $(MCU)),) + # Cortex version + MCU = cortex-m0plus + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + CHIBIOS_PORT = ARMv6-M-RP2 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = RP + MCU_SERIES = RP2040 + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + STARTUPLD_CONTRIB = $(CHIBIOS_CONTRIB)/os/common/startup/ARMCMx/compilers/GCC/ld + MCU_LDSCRIPT ?= RP2040_FLASH_TIMECRIT + LDFLAGS += -L $(STARTUPLD_CONTRIB) + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= rp2040 + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_PROMICRO_RP2040 + + # Default UF2 Bootloader settings + UF2_FAMILY ?= RP2040 + FIRMWARE_FORMAT ?= uf2 +endif + +ifneq ($(findstring STM32F042, $(MCU)),) + # Cortex version + MCU = cortex-m0 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 6 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F0xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32F042x6 + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f0xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F042X6 + + USE_FPU ?= no + + # UF2 settings + UF2_FAMILY ?= STM32F0 + + # Stack sizes: Since this chip has limited RAM capacity, the stack area needs to be reduced. + # This ensures that the EEPROM page buffer fits into RAM + USE_PROCESS_STACKSIZE = 0x600 + USE_EXCEPTIONS_STACKSIZE = 0x300 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFFC400 +endif + +ifneq ($(findstring STM32F072, $(MCU)),) + # Cortex version + MCU = cortex-m0 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 6 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F0xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32F072xB + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f0xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F072XB + + USE_FPU ?= no + + # UF2 settings + UF2_FAMILY ?= STM32F0 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFFC800 +endif + +ifneq ($(findstring STM32F103, $(MCU)),) + # Cortex version + MCU = cortex-m3 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F1xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + ifeq ($(strip $(BOOTLOADER)), uf2boot) + MCU_LDSCRIPT ?= STM32F103xB_uf2boot + else + MCU_LDSCRIPT ?= STM32F103x8 + endif + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f1xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F103 + + USE_FPU ?= no + + # UF2 settings + UF2_FAMILY ?= STM32F1 +endif + +ifneq ($(findstring STM32F303, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F3xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + ifeq ($(strip $(BOOTLOADER)), tinyuf2) + MCU_LDSCRIPT ?= STM32F303xC_tinyuf2 + else + MCU_LDSCRIPT ?= STM32F303xC + endif + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f3xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F303XC + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32F3 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFFD800 +endif + +ifneq ($(findstring STM32F401, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + ifeq ($(strip $(BOOTLOADER)), tinyuf2) + MCU_LDSCRIPT ?= STM32F401xC_tinyuf2 + else + MCU_LDSCRIPT ?= STM32F401xC + endif + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F401XC + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32F4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 + + # Revert to legacy wear-leveling driver until ChibiOS's EFL driver is fixed with 128kB and 384kB variants. + EEPROM_DRIVER ?= wear_leveling + WEAR_LEVELING_DRIVER ?= legacy +endif + +ifneq ($(findstring STM32F405, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32F405xG + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F405XG + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32F4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq ($(findstring STM32F407, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32F407xE + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F407XE + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32F4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq ($(findstring STM32F411, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + ifeq ($(strip $(BOOTLOADER)), tinyuf2) + MCU_LDSCRIPT ?= STM32F411xE_tinyuf2 + else + MCU_LDSCRIPT ?= STM32F411xE + endif + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F411XE + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32F4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq ($(findstring STM32F446, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32F4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32F446xE + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32f4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_F446XE + + USE_FPU ?= yes + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 + + # Default as no chibios efl config + EEPROM_DRIVER ?= transient +endif + +ifneq ($(findstring STM32G431, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32G4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32G431xB + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32g4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_G431XB + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32G4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq ($(findstring STM32G474, $(MCU)),) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32G4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32G474xE + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32g4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_G474XE + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32G4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq (,$(filter $(MCU),STM32L432 STM32L442)) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32L4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32L432xC + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32l4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_L432XC + + PLATFORM_NAME ?= platform_l432 + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32L4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq (,$(filter $(MCU),STM32L433 STM32L443)) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32L4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32L432xC + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32l4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_L433XC + + PLATFORM_NAME ?= platform_l432 + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32L4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq (,$(filter $(MCU),STM32L412 STM32L422)) + # Cortex version + MCU = cortex-m4 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32L4xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32L412xB + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32l4xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_L412XB + + PLATFORM_NAME ?= platform_l412_l422 + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32L4 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 +endif + +ifneq ($(findstring WB32F3G71, $(MCU)),) + # Cortex version + MCU = cortex-m3 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = WB32 + MCU_SERIES = WB32F3G71xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= WB32F3G71x9 + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= wb32f3g71xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_WB32_F3G71XX + + USE_FPU ?= no + + # Bootloader address for WB32 DFU + WB32_BOOTLOADER_ADDRESS ?= 0x1FFFE000 +endif + +ifneq ($(findstring WB32FQ95, $(MCU)),) + # Cortex version + MCU = cortex-m3 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = WB32 + MCU_SERIES = WB32FQ95xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= WB32FQ95xB + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= wb32fq95xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_WB32_FQ95XX + + USE_FPU ?= no + + # Bootloader address for WB32 DFU + WB32_BOOTLOADER_ADDRESS ?= 0x1FFFE000 +endif + +ifneq ($(findstring GD32VF103, $(MCU)),) + # RISC-V + MCU = risc-v + + # RISC-V extensions and abi configuration + MCU_ARCH = rv32imac + MCU_ABI = ilp32 + MCU_CMODEL = medlow + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_PORT_NAME = GD + MCU_FAMILY = GD32V + MCU_SERIES = GD32VF103 + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/RISCV-ECLIC/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= GD32VF103xB + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/RISCV-ECLIC/compilers/GCC/mk/ + MCU_STARTUP ?= gd32vf103 + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= SIPEED_LONGAN_NANO + + USE_FPU ?= no +endif |